Nilight Flush Mount LED Pods 2PCS 6 Inch 60W LED Work Light Flood Spot Beam Combo Backup Driving Lights Fog Lamp Reverse Grill Mount Lighting for Offroad 4x4 Truck SUV

The OEM halogen reversing and side area lights on our 2006 Travel Supreme Select were more rust inside than intact reflector/deflector. Remarkably, half of them still worked, though they were more like a couple of candles, not halogen lamps.These were easy to install, the template is nice, hardware looks nice, and the lamps themselves are not cheap-feeling. Solid, large metal heat sink. I do wish there were more flood than spot, but that's a personal thing.

Wasn't too sure about these when I saw them online. I was expecting something cheaply made and something that felt equally cheap in my hand. I was pleasantly surprised when I opened the box and unpacked the contents. Everything was well packaged and nothing was scratched or damaged. The lights are heavy gauge metal body construction and are very sturdily built. I wouldn't recommend using the cardboard template though. U installed the first one without using it and everything came out good. Using the template, the holes were off a little and had to be bored out a little larger in order to get the bolt through the hole. Just slide the light through the cutout you make then mark the mounting holes and drill - perfect fit. I can't wait to see the difference these things make. As you can see in the picture, the bag contains bolts, buts and washers. It also contains an allen wrench to tighten the bolts.I could barely tell when my factory reverse lamps came on. After installing these lamps, I can clearly see when I am backing up. I get great illumination at least 50 feet behind my truck now; more than enough to safely back up without worry. I hope to get a long life of use from these, but if I were still deciding on which set to buy, I'd choose these.As I was installing them, a neighbor came by and said they looked great on the truck and that they didn't look aftermarket or out of place at all.All-in-all I would say the install is fairly easy with minimal "mechanical knowledge" required. Tools required: 4 1/2" grinder to cut through the bumper, needle nose vice grips, marker, drill with bit. On a 1 (easy) to 10 (hard) scale I'd give the install procedure a 2.The last picture shows the lights on. You can see the OEM reverse lights under the tail lights Huge difference.******UPDATE******About a week after installing the lights, I noticed one light was not working. I have not figured out yet what the problem is. I was thinking it was shorting out but that doesn't seem to be the problem. If I tap the back of the light, it will turn on (as long as it is suppose to be on). Now I am thinking it is defective.

I bought these as a back up camera light and all I can say is that it’s worth the install these are super super bright to the point you can’t forget to leave them on a drive off because you’ll blind the people behind you lol

These are bright, but much more of a scattered flood than I was hoping for there's not much focus if any for the light beam. I have other nitlight lights on another truck they are a little smaller and have a more focused beam to them. Install is straight forward and difficult do to my choice of 1/4" diamondplate on my homemade bumper should be easy on anything else just make sure you aren't planning on cutting the holes with a 4.5" grinder there's no room for the corners to cover any overcut. So I started with grinder ended with Sawzall. They look nice very low profile now I just need to figure out how to keep them from lighting up the sky and keep them a bit more tamed toward the ground. This is not a defect just a flood light with a very impressive spread more than my personal preference

I use them as backup lights, They're very bright. I took a cutting wheel on it 4 1/2 inch grinder cut and cut out a square then mounted them in and wired them to my back up light wiring. They work great a lot better than the factory backup lights.

Easy to install and looks great on flatbeds

These lights absolutely exceeded my expectations! They feel of very good quality and they are very bright as well. I used them to add some light to the back of my truck so they are wired into my reverse lights and mounted inside of my bumper. They were easy to install, easy to use, and helped tremendously.

This is the 2nd set I bought. 1st set lasted about 6 years in my rear bumper. Rear tires constantly covering them with mud, water, snow/salt. They held up great but eventually failed. Replaced them with the exact same light cause I was happy with how long they lasted. I would but then again. Very bright.

Bien

Muy buena calidad y la luz blanca

Purchased to install as auxiliary back up lights on my truck. Very happy with them, very bright, nice clean white light. More of a spot than a flood, but really nice lights. Not sure on reliability yet, but seem like pretty decent quality foe the price.

👍

Se sienten bien aúno los instalo pero se ve de buenos materiales después actualizo la reseña